hjem | hjelp | email  








 SRHaugen
Strømmen
926 06 651

 

Yak-130







Flys på 6S 3300mAh batteri





Brukermanual Yak-130


Brukermanual ZTW Gecko ESC




Change Sun 70mm XRP vifte

- Rotor Material : Carbon Fiber Reinforced Nylon

- Rotor Diameter : 68mm , 14 Blade

- Spinner Material: Alu Spinner

- Shroud O.D.: 72.0mm

- Stator Number: 9

- Weight: 245g

- Working Voltage : 18.5 - 22.2v (5 - 6S)

- Motor : Cyclone Power IR550-2200-40

- ESC: ZTW Gecko 85A Brushless ESC With 8A Adjustable SBEC

- Static Thrust: 5S 1600g (57A) , 6S 2100g (75A)






Vifte og motor montert i flykroppen.

ZTW Gecko 85A Brushless ESC

With 8A Adjustable SBEC

ZTW GECKO SERIES Airplane/Heli ESCs are competition-grade speed controllers from one of the most trusted RC electronics manufacturers in the industry. NEW FEATURES found in Gecko Series ESCs include PC data logging, firmware upgradability, and an 8A SBEC adjustable up to 8.4v to help your HV servos reach their fullest potential! Best of all, Gecko Series ESCs come standard with the ZTW quality, performance, and reliability you have come to trust.

The high power SBEC found in ZTW Gecko Series ESCs has been specifically designed for extreme aerobatics and therefore has the capability to support the higher momentary peak demand loads to eliminate the possibility of unwanted shutdowns, and is also capable of supporting continuous simultaneous multiple servo operations typically found in CCPM equipped hardcore 3D E-helicopters.

Features:

Data logging via PC interface (optional accessory included with program card)

Firmware upgradable via PC interface

High SBEC current output: 8A continuous, 16A burst

Adjustable SBEC voltage up to 8.4v for optimum performance from HV servos

Extremely low internal resistance

Smooth and accurate throttle linearity

Power arming protection, over-heat protection, low-voltage protection and lost signal protection

Supports high RPM motors

Advanced governor mode and soft start

Optional programming card & PC USB interface available

 

Specifications:

Output: 85A continuous, 100A burst for 10 seconds

Input voltage: 2-6s LiPo; 5-18 cell Ni-XX

SBEC output: 5.0v / 6.0v / 7.4v / 8.4v adjustable @ 8A (switching)

Weight: 74g

Dimensions: 66 x 33 x 16mm

Programmable Options:

Brake setting (off / soft / mid / hard -- default: off)

Battery type: (Ni-XX / LiPo / LiFe -- default: LiPo auto detect)

Cut-off voltage threshold (2.8V 50% / 3.0V 60% / 3.2V 65% / No protection -- default: 3.0V 60%)

Factory default setup reset

Timing settings (auto / 2° / 8° / 15° / 22° / 30° -- default: auto)

SBEC Voltage Output (5.0v / 6.0v / 7.4v / 8.4v -- default: 5.0v)

Governor mode: (RPM off / 1st Soft Start / 2nd Soft Start / Gov Mode 1 / Gov Mode 2 -- default: RPM off)

Motor rotation: (forward / reverse -- default: forward)

Start up (Low / Mid / High-- default: 30%)

LVC cut-off type: (reduce gradually / cut-off -- default: reduce gradually)




Copyright 2018 - Kongeplass - All Rights Reserved

 

[ hjem ] mine modeller ] prosjekter ] linker ] [ bilder ] familiearkiv ]